Home > Glue Dispenser

  • Glue Dispensing Machine Glue Dispenser Equipment,CW-300M
Glue Dispensing Machine Glue Dispenser Equipment,CW-300M

Glue Dispensing Machine Glue Dispenser Equipment,CW-300M

  • Product description: Glue Dispensing Machine Glue Dispenser Equipment,CW-300M
  • INQUIRY

Glue Dispensing Machine Glue Dispenser Equipment,CW-300M


Glue Dispensing Machine Glue Dispenser Equipment,CW-300M  Description:

The 300MM Stepper is our most popular industrial robot with a dispensing area of 11.81" x 11.81" (300MM X 300MM). The 300MM Cartesian robot represents a substantial cost saving in comparison to similar desktop robots. Its overall footprint has a depth of less than 26 inches (640MM), suitable for an industrial bench. This line of robots is also available with a low cost vision system.

These bench top industrial robots are ideal for automating a current dispensing application. With the various work areas offered almost every application can be fitted on one of the models in this series; 200, 300 or 400MM Robots.

A program consists of a series of instructions stored in the main unit, each instruction stored in a numbered memory address. An address may record a point location, X, Y, and Z axis value, point type or instruction which sets a certain parameter, such as a dispensing time or line speed.

Installation:

The automatic dispenser machine can satisfy various requirements for dispensing, only need to choose different fixtures and math with dispensing systems. 



Glue Dispensing Machine Glue Dispenser Equipment,CW-300M Technical parameters:

 X/Y/Z Work Area: 300/300/100 MM

Work Load: Table/Tool: 10 kg./5 kg.

Max. Speed:  X&Y/Z  800/320 (mm/sec)

Repeat ability: +/- 0.02 mm/axis

Resolution: 0.001 mm/axis

Data Memory: 100 Programs/50,000 points per

Drive System: Micro stepping motor

Motion Control: Point to point & continuous path

Teaching Method: Teach Pendant

I/O Signals: 8 inputs/8 outputs

External Interface: USB/RS232

Power Supply: 100-240 VAC, 320W



Glue Dispensing Machine Glue Dispenser Equipment,CW-300M Detailed Product Description

Work Areas:

19.68" X 19.68"

X/Y/Z Work Area:

300/300/100 MM

Repeatability:

+/- 0.01mm / Axis

Interpolation Function::

3 Axis

I/O Signals Port:

8 Inputs / 8 Outputs

Trade Term::

EXW

Automated Dispensing Robot Machines Glue Dispenser Robot For Electronic Assembly


Glue Dispensing Machine Glue Dispenser Equipment,CW-300M Installation Instruction:

1. The standard accessories include the 30CC needle cylinder clamps, and they can be applied to 30CC or 55CC needle cylinder. If you want to use other needle cylinder, then you have to purchase other needle cylinder clamps appropriate. 

2. Fix the needle cylinder clamps onto the Z axle. Put the hexagon socket flat head screws through the holes of the clamps and then lock on the Z ground side. The clamp has a couple of holes to select, according to the specific requirements .

3. Connect the signal port(three holes) of the dispenser machine on the backside to the signal port in the controller with dispenser signal line. The signal port in the dispenser machine is the same one that connecting with the foot-plate. Thus a problem may appear that the port can not be shared, if your dispenser machine is not purchased along with the matching machine. In such case, please contact us for joint exchanging.

4. Connect the compressed air source to the dispenser controller, put the needle cylinder collet onto the needle cylinder and tighten it, and put the needle cylinder into the needle cylinder clamps and lock the screws which are used to fix the needle cylinder.( Please dont over tighten, in case of deformation. And once it deforms, the piston then cannot fit with the inner side of the needle cylinder, and cause air leakage.)

5. Connect the hand held programmer to the machine.

6. Connect the dispenser machine and the controller to 220V power source.

7. Do make sure the pressure pipe of the needle cylinder collect and the power source will not influence the motion of each axles and working plate.



Glue Dispensing Machine Glue Dispenser Equipment,CW-300M Our Vision:


Ongoing PCB industry PCB separator technological innovation, to create greater value, allowing customers to success


Glue Dispensing Machine Glue Dispenser Equipment,CW-300M  Why us:

1.Engineers available to service machinery oversea.

Engineers are available to be sent to foreign countries to do machinery training and offer technical support.

2.Mature technique & forerunner to process makes high quality machinery.  

As largest manufactory in South China, we have 12 years experience on PCB separator machines and soldering machines. pcb router machine

Our R&D team continuously upgrade the existing machines to meet the market development trend.

3.Effective customer service. pcb router machine

All of us together are stronger and wiser than any one of us individually. To succeed, we must assume responsibility, cooperate with fellow associates and with departments, effectively communicate with one another, foster enthusiasm and participate in decision-making. To be seay reachable by customers and provide prompt replies to solve their problems and create value for customers.

4.One year warranty for the machines except accessories. b router machine

Robust frame construction and Japanese steel blades obtained good appraise and recognized by and oversea clients. We offer parts for replacement under warranty free of charge, clients only need to bear freight charge.

 



 

 



CONTACT US

Contact: Doreen

Phone: 13537348526 (Skype:s2@smtfly.com)

Tel: 86-0755-33581320

Email: s2@smtfly.com

Add: Building 2, Gang Hua Xing Industrial Park, Chongqing Road, Fuyong Town, Shenzhen, China 518103